en-us_products:mp_studio:menus_settings

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
en-us_products:mp_studio:menus_settings [2026/11/05 11:42] – external edit 127.0.0.1en-us_products:mp_studio:menus_settings [2026/11/12 20:37] (current) – external edit 127.0.0.1
Line 29: Line 29:
 ^ Item ^ Shortcut ^ Action ^ ^ Item ^ Shortcut ^ Action ^
 | Show Symbols · Show Comments | — | Shows symbol names and comments on the cells. | | Show Symbols · Show Comments | — | Shows symbol names and comments on the cells. |
-| Bookmark List | — | Shows or hides the bookmark (Mark) list at the bottom of the Functions panel. | +| Bookmark List | — | Shows or hides the bookmark list at the bottom of the Functions panel. | 
-| Symbol Rail · Functions · Inspector · Watch · Command Bar · Status Pills | ''Alt+1'' to ''Alt+7'' | Shows or hides each panel. |+| Symbol Rail · Functions · Inspector · Watch · Command Bar · Status Indicators | ''Alt+1'' to ''Alt+7'' | Shows or hides each panel. |
 | Hide All Panels | ''Alt+0'' | Hides all panels. | | Hide All Panels | ''Alt+0'' | Hides all panels. |
 | Zoom In · Zoom Out · Fit to Width | ''Ctrl+='' · ''Ctrl+-'' | Changes the display size of the ladder. ''Ctrl+0'' returns to 100%. | | Zoom In · Zoom Out · Fit to Width | ''Ctrl+='' · ''Ctrl+-'' | Changes the display size of the ladder. ''Ctrl+0'' returns to 100%. |
Line 48: Line 48:
 | Data Table | — | [[:en-us_products:mp_studio:monitoring#data_table|Phase 7]] | | Data Table | — | [[:en-us_products:mp_studio:monitoring#data_table|Phase 7]] |
 | Program Memory | — | [[:en-us_products:mp_studio:download#program_memory|Phase 6]] | | Program Memory | — | [[:en-us_products:mp_studio:download#program_memory|Phase 6]] |
-| FORCE INPUT / OUTPUT | — | [[:en-us_products:mp_studio:monitoring#forced_input_and_output|Phase 7]] |+| Force Input/Output | — | [[:en-us_products:mp_studio:monitoring#forced_input_and_output|Phase 7]] |
 | Clear EEPROM | — | [[:en-us_products:mp_studio:download#clear_eeprom|Phase 6]] | | Clear EEPROM | — | [[:en-us_products:mp_studio:download#clear_eeprom|Phase 6]] |
-| Set Device Clock… | — | Sets the device clock (RTC) to the PC time and reads it back to confirm it took. |+| Set PLC Clock… | — | [[:en-us_products:mp_studio:device_clock|PLC Clock (RTC)]] |
 | Mnemonic | — | [[:en-us_products:mp_studio:download#mnemonic_conversion|Phase 6]] | | Mnemonic | — | [[:en-us_products:mp_studio:download#mnemonic_conversion|Phase 6]] |
  
-===== Setting Menu =====+===== Settings Menu =====
  
-{{ :en-us_products:mp_studio:menu-setting.png?480 |Figure 5. The Setting menu }}+{{ :en-us_products:mp_studio:menu-setting.png?480 |Figure 5. The Settings menu }}
  
  
Line 61: Line 61:
 | Communication Port | Sets the download channel and the serial channels. [[:en-us_products:mp_studio:download#communication_port|Phase 6]] | | Communication Port | Sets the download channel and the serial channels. [[:en-us_products:mp_studio:download#communication_port|Phase 6]] |
 | 언어: 한국어 · Language: English · 言語: 日本語 | Changes the display language. | | 언어: 한국어 · Language: English · 言語: 日本語 | Changes the display language. |
-| Option | Sets the grid, fonts, colors and brand name. |+| Options | Sets the grid, duplicate coil check, timer base, fonts, colors and brand name. |
 | Data Memory | Sets the memory area sizes and retentive ranges. [[:en-us_products:mp_studio:memory_symbols#data_memory|Phase 5]] | | Data Memory | Sets the memory area sizes and retentive ranges. [[:en-us_products:mp_studio:memory_symbols#data_memory|Phase 5]] |
 | Symbol | Opens the symbol table. [[:en-us_products:mp_studio:memory_symbols#symbol_table|Phase 5]] | | Symbol | Opens the symbol table. [[:en-us_products:mp_studio:memory_symbols#symbol_table|Phase 5]] |
-| LCD Screen Editor | Creates screens to show on a character LCD. The ladder shows a screen with the ''CSCR'' function. | +| CLCD Screen Editor | Creates screens to show on a character LCD. The ladder shows a screen with the ''CSCR'' function. [[:en-us_products:mp_studio:lcd_screen_editor|CLCD Screen Editor]] | 
-| Device | Selects the model and expansion modules. [[:en-us_products:mp_studio:first_project#3_new_project_and_model_selection|Phase 1]] | +| 7-Segment Screen Editor | Creates screens to show on a 7-segment display. The ladder shows a screen with the ''FSCR'' function. [[:en-us_products:mp_studio:seven_segment|7-Segment Display]] | 
-| Modbus RTU Master | Sets up the Modbus RTU master communication list. | +| Device | Selects the model and expansion modules. [[:en-us_products:mp_studio:first_project#new_project_and_model_selection|Phase 1]] | 
-| RTC (Clock)… | Sets the start address of the D area (16 words) where the device writes the date, time and status of an external DS3231 module every 0.1 seconds. |+| Modbus RTU Master | Sets up Modbus RTU master communication. [[:en-us_products:mp_studio:modbus_device_table|Modbus Device Table]] | 
 +| RTC (Clock)… | Sets the start address of the D area (16 words) where the PLC writes the date, time and status of an external DS3231 module every 0.1 seconds. [[:en-us_products:mp_studio:device_clock|PLC Clock (RTC)]] | 
 +| Input Filter… | Sets the time used to filter out chatter and noise on digital inputs, as a default and as per-input values (V1.4.0 and later). [[:en-us_products:mp_studio:input_filter|Input Filter]] | 
 +| User Protocol… | Defines, per communication port, the frames and transactions to exchange with devices that do not use Modbus (V1.3.0 and later). [[:en-us_products:mp_studio:user_protocol|User Protocol]] |
 | Theme: Modern Dark · VS Code · Light | Changes the screen theme. | | Theme: Modern Dark · VS Code · Light | Changes the screen theme. |
  
 ===== Options ===== ===== Options =====
  
-Select **Setting → Option** or click the **Options** button in the top band to open the **Option** window. Choose an item in the navigation on the left to see its settings and a preview on the right.+Select **Settings → Options** or click the **Options** button in the top band to open the **Options** window. Choose an item in the navigation on the left to see its settings and a preview on the right.
  
-{{ :en-us_products:mp_studio:settings-dialog-marked.svg?1200 |Figure 6. The Option window }}+{{ :en-us_products:mp_studio:settings-dialog-marked.svg?1080 |Figure 6. The Options window }}
  
   * **① Search settings:** finds items by setting name.   * **① Search settings:** finds items by setting name.
-  * **② Navigation:** Grid, FONT, COLOR and Brand name+  * **② Navigation:** Grid & duplicate coils, FONT, COLOR and Brand name
   * **③ Settings area**   * **③ Settings area**
   * **④ Preview:** changed settings are reflected in the ladder preview right away.   * **④ Preview:** changed settings are reflected in the ladder preview right away.
Line 83: Line 86:
  
 ^ Navigation ^ Settings ^ ^ Navigation ^ Settings ^
-| Grid | Cell width and height (Grid width, Grid height), the number of cells per row (Columns per row), and Check for duplicate coils | +| Grid & duplicate coils | Cell size (Cell width, Cell height), the number of cells per row (Cells per row), Check for duplicate coils, and [[#timer_base|Timer base]] | 
-| FONT | Grid Font (addresses, symbols, comments and monitor values), Header Font (row numbers), Interface font (menus and windows), Code font (places that show addresses and values in a fixed-width font) |+| FONT | Grid font (addresses, symbols, comments and monitor values), Header font (row numbers), Interface font (menus and windows), Fixed-width font (places that show addresses and values in fixed-width type) |
 | COLOR | Colors for the Theme, Ladder, Function blocks, Monitor & check, and Interface | | COLOR | Colors for the Theme, Ladder, Function blocks, Monitor & check, and Interface |
 | Brand name | The name shown in the window title | | Brand name | The name shown in the window title |
  
-Columns per row applies only to the project. Custom colors apply to every theme, and colors you leave unset follow the selected theme. Printing always uses paper colors (black).+Cells per row, Check for duplicate coils and Timer base apply only to the project. Custom colors apply to every theme, and colors you leave unset follow the selected theme. Printing always uses paper colors (black).
  
 {{ :en-us_products:mp_studio:settings-colors.png?1080 |Figure 7. COLOR › Ladder settings and the preview }} {{ :en-us_products:mp_studio:settings-colors.png?1080 |Figure 7. COLOR › Ladder settings and the preview }}
 +
 +==== Timer Base ====
 +
 +In **Grid & duplicate coils**, use **Timer base** to choose the time unit that timers and clocks (''@n'', ''@Fn'') count in: **10 ms (default)** or **1 ms** (V1.3.0 and later). You can choose it only while a project is open, and a new project starts with 10 ms.
 +
 +^ Item ^ 10 ms (default) ^ 1 ms ^
 +| Set value written as a number only (''TON T0 100'') | 1 second | 0.1 seconds |
 +| Set value with a unit (''TON T0 1s'') | 1 second | 1 second |
 +| ''@100'' | ON for one scan every second | ON for one scan every 0.1 seconds |
 +| ''@F100'' | 2-second period | 0.2-second period |
 +| Longest timer time (''BT'', ''T'', ''DT'') | 2.55 s, 655 s, 497 days | 0.255 s, 65.5 s, 49.7 days |
 +
 +Even with 1 ms, timers check the time once per scan, so the real resolution cannot be finer than the scan time. You do not need to change the PLC firmware. Values written as ×10 ms (the timeout of the Modbus RTU Master and the EEPROM update cycle of Data Memory) and SCAN TIME stay in 10 ms units regardless of the timer base. The 1 ms base uses 5 more bytes of PLC RAM, and if there is not enough RAM, a compile error is shown.
 +
 +When you change the base and click **OK** (or **Apply**), the **Change timer base** window shows the number of affected cells, if there are any.
 +
 +  * **Adjust values too (keep the same time):** changes the timer set values and clock numbers written as numbers so that the times stay the same. From 10 ms to 1 ms they are multiplied by 10; from 1 ms to 10 ms they are divided by 10 (the remainder is dropped, and a result below 1 becomes 1).
 +  * **Keep numbers:** changes only the base. The times become 1/10 when you go from 10 ms to 1 ms, and 10 times longer when you go from 1 ms to 10 ms.
 +  * **Cancel:** returns to the Options window without changing the base.
 +
 +Timer set values written as variables, cells that read the current value of a timer, and timer cells that will go out of range (red) after the change are counted separately in the window, so check them yourself. A single ''Ctrl+Z'' undoes the new base and the adjusted values together. To keep them in the file, save the project. A project that uses 1 ms shows **Timer 1 ms** in the status indicators. A ''.mpx'' file saved with 1 ms cannot be opened by V1.2.0 and earlier.
  
 ===== Themes and Language ===== ===== Themes and Language =====
  
-In the **Setting** menu, choose **Theme: Modern Dark**, **Theme: VS Code** or **Theme: Light**.+In the **Settings** menu, choose **Theme: Modern Dark**, **Theme: VS Code** or **Theme: Light**.
  
 {{ :en-us_products:mp_studio:theme-modern.png?380 |Modern Dark}} {{ :en-us_products:mp_studio:theme-vscode.png?380 |VS Code}} {{ :en-us_products:mp_studio:theme-light.png?380 |Light}} {{ :en-us_products:mp_studio:theme-modern.png?380 |Modern Dark}} {{ :en-us_products:mp_studio:theme-vscode.png?380 |VS Code}} {{ :en-us_products:mp_studio:theme-light.png?380 |Light}}
  
-Use **언어: 한국어**, **Language: English** and **言語: 日本語** in the **Setting** menu to change the language of the menus and windows. The three items are always shown in their own language, whichever language the screen is in, so you can return to English from any screen by choosing **Language: English** (in Korean the menu is named **설정**, in Japanese **設定**).+Use **언어: 한국어**, **Language: English** and **言語: 日本語** in the **Settings** menu to change the language of the menus and windows. The three items are always shown in their own language, whichever language the screen is in, so you can return to English from any screen by choosing **Language: English** (in Korean the menu is named **설정**, in Japanese **設定**).
  
-{{ :en-us_products:mp_studio:language-english.png?1000 |Figure 8. The Setting menu with the three language items }}+{{ :en-us_products:mp_studio:language-english.png?1000 |Figure 8. The Settings menu with the three language items }}
  
 ===== Printing ===== ===== Printing =====
Line 110: Line 134:
 ===== Modbus RTU Master ===== ===== Modbus RTU Master =====
  
-Select **Setting → Modbus RTU Master** to open a window for setting up the list of registers that the device, acting as a Modbus RTU master, reads from and writes to other devices.+Select **Settings → Modbus RTU Master** to open a window for setting up the registers that the PLC, acting as a Modbus RTU master, reads from and writes to other devices. New projects and projects that have a device table open the [[:en-us_products:mp_studio:modbus_device_table|Modbus Device Table]] window; projects that have only a list made in the previous MP STUDIO (such as the bundled Modbus example) open the list window below.
  
-{{ :en-us_products:mp_studio:modbus-master-marked.svg?940 |Figure 10. The MODBUS MASTER SETTING window (bundled Modbus example) }}+{{ :en-us_products:mp_studio:modbus-master-marked.svg?940 |Figure 10. The Modbus Master List window (bundled Modbus example) }}
  
-  - In **① Communication Port**, choose the channel to use as the master (**Comm Port 1** to **Comm Port 3**), and set the Baud Rate, Data Bits, Stop Bits, Parity, Timeout (×10 ms) and Delay (ms).+  - In **① Communication Port**, choose the channel to use as the master (**Comm Port 1** to **Comm Port 3**), and set the Baud rate, Data bits, Stop bits, Parity, Timeout (×10 ms) and Delay (ms).
   - Click **② Add** to add an item. **Sort** sorts the items.   - Click **② Add** to add an item. **Sort** sorts the items.
-  - In **③ the item table**, enter the **Modbus Code** (for example ''WORD READ ( FC03 )'' or ''WORD WRITE ( FC06 )''), **Slave ID**, **Address**, **Binding** (the device memory that exchanges the value, for example ''D10'') and **Description** on each row. Click **Delete** at the end of a row to remove that item.+  - In **③ the item table**, enter the **Function code** (for example ''WORD READ ( FC03 )'' or ''WORD WRITE ( FC06 )''), **Slave ID**, **Address**, **Binding** (the PLC memory that exchanges the value, for example ''D10'') and **Description** on each row. Click **Delete** at the end of a row to remove that item.
   - Click **OK** to save.   - Click **OK** to save.
  
 When you click OK, the communication settings of the selected channel change to the values above, its mode is set to ''Modbus RTU Master'', and download on that channel is turned off. When you click OK, the communication settings of the selected channel change to the values above, its mode is set to ''Modbus RTU Master'', and download on that channel is turned off.
  
-Click **Move to table** at the bottom left of the window to move this list into the Modbus device table. Moving it changes the compiled program (it then uses the device table's new communication method). Use **Edit → Undo** (''Ctrl+Z'') to move it back.+Click **Move to table** at the bottom left of the window to move this list into the [[:en-us_products:mp_studio:modbus_device_table|Modbus Device Table]]. Moving it changes the compiled program (it then uses the device table's new communication method). Use **Edit → Undo** (''Ctrl+Z'') to move it back.
  
 ===== Autosave and Recovery ===== ===== Autosave and Recovery =====
  
-MP STUDIO 2 automatically saves the project you are editing. If the program closed without saving, the **Recover autosave** window appears the next time you start it.+MP STUDIO 2 automatically saves the project you are editing. If the program closed without saving, the **Recover Autosave** window appears the next time you start it.
  
   * **Yes:** opens the autosaved copy.   * **Yes:** opens the autosaved copy.
-  * **No:** deletes the autosaved copy.+  * **Delete:** deletes the autosaved copy.
   * **Cancel:** keeps the autosaved copy without deleting it. You can open it later from **Project → Recover Autosave…**.   * **Cancel:** keeps the autosaved copy without deleting it. You can open it later from **Project → Recover Autosave…**.
  
-{{ :en-us_products:mp_studio:autosave-recover.png?440 |Figure 11. The Recover autosave window }}+{{ :en-us_products:mp_studio:autosave-recover.png?440 |Figure 11. The Recover Autosave window }}
  
 ===== Help Menu ===== ===== Help Menu =====
Line 140: Line 164:
 | About MP STUDIO 2 | Shows the program version and information. | | About MP STUDIO 2 | Shows the program version and information. |
 | Homepage | Opens the ILOGICS homepage. | | Homepage | Opens the ILOGICS homepage. |
-| SW Manual | Opens the software manual. | +| Software Manual | Opens the software manual. | 
-| HW Manual | Opens the hardware manual of the selected model. | +| Hardware Manual | Opens the hardware manual of the selected model. | 
-| Report a Problem… | Describe a problem, attach a screenshot or the project file, and send it to the developer. |+| Report a Problem… | Describes a problem, attaches a screenshot or the project file, and sends it to the developer. |
 | Request an Improvement… | Sends a feature you would like or an improvement to the developer. | | Request an Improvement… | Sends a feature you would like or an improvement to the developer. |
 | Send Error Reports Automatically | When checked (✓), diagnostic information is sent automatically when an error occurs. | | Send Error Reports Automatically | When checked (✓), diagnostic information is sent automatically when an error occurs. |
en-us_products/mp_studio/menus_settings.1793846531.txt.gz · Last modified: by 127.0.0.1

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki