Differences

This shows you the differences between two versions of the page.

--- en-us_products:mpino_8a4t_s [2026/09/07 21:52] – 바깥 편집 127.0.0.1
+++ en-us_products:mpino_8a4t_s [2026/10/25 08:42] (current) – external edit 127.0.0.1
@@ Line 4: / Line 4: @@
 Program the controller with Arduino IDE (Arduino C/C++) or MPINO STUDIO 2 (Arduino C/C++ & ladder logic).
+See the [[:en-us_products:mpino_series#mpino_series_specifications|MPINO Series specifications]] for the board name, connection method, and first I/O numbers for MPINO-8A4T-S.
 {{ :en-us_products:mpino-8a4t-s-connectors.svg?nolink |MPINO-8A4T-S connector guide }}
@@ Line 12: / Line 18: @@
 |  Power  |  -  |  Supply voltage  | DC 12~24V (0.5A or more when using DC 24V)  |
 |  Digital inputs  |  8 points \\ (Solid-state, isolated)  |  P0~P7  | operating input voltage: DC 0~40V \\ HIGH detection voltage: DC 5V or higher \\ 8 points/1COM \\ NPN/PNP input support  |
-|  Transistor outputs  |  4 points \\ (Solid-state, isolated)  |  P32~P35  | Output type: SINK \\ Output operation: connected to V- when ON \\ maximum allowable output current: 1A/1 points \\ load voltage: DC 0~100V \\ Connect the load supply to V+ and V-  |
+|  Transistor outputs  |  4 points \\ (Solid-state, isolated)  |  P32~P35  | Output type: SINK \\ Output operation: connected to V- when ON \\ maximum allowable output current: 1A/1 point \\ load voltage: DC 0~100V \\ Connect the load supply to V+ and V-  |
-|  Analog inputs  |  2 points \\ (Non-isolated)  |  A0, A1  | input voltage: DC 0~5V \\ resolution: 10bit (0~1023) \\ input resistance: 100MΩ (±1%)  |
+|  Analog inputs  |  2 points \\ (Non-isolated)  |  A0, A1  | input voltage: DC 0~5V \\ resolution: 10-bit (0~1023) \\ input resistance: 100MΩ (±1%)  |
-|  Analog inputs  |  2 points \\ (Non-isolated)  |  A2, A3  | input current: 0~20mA or 4~20mA \\ Resolution: 0~20mA is 10bit (0~1023); 4~20mA is 0~818 \\ input resistance: 250Ω (±1%)  |
+|  Analog inputs  |  2 points \\ (Non-isolated)  |  A2, A3  | input current: 0~20mA or 4~20mA \\ Resolution: 0~20mA is 10-bit (0~1023); 4~20mA is 0~818 \\ input resistance: 250Ω (±1%)  |
-|  Analog inputs  |  2 points \\ (Non-isolated)  |  A4, A5  | input voltage: DC 0~10V \\ resolution: 10bit (0~1023) \\ input resistance: 200kΩ (±1%)  |
+|  Analog inputs  |  2 points \\ (Non-isolated)  |  A4, A5  | input voltage: DC 0~10V \\ resolution: 10-bit (0~1023) \\ input resistance: 200kΩ (±1%)  |
 |  Temperature sensor inputs  |  2 points \\ (Non-isolated)  |  NTEMP \\ A6, A7  | input temperature: -40~120℃ \\ Sensor: NTC 3950K, 10kΩ(25℃) \\ Resolution: 0.1℃ (at 0~40℃)  |
 |  Interrupts \\ High-Speed Counter / Encoder  |  4 points \\ (Non-isolated)  |  D24(CLK), D25(DIO) \\ D18(SCL), D19(SDA)  | input voltage: DC 0~5V \\ HIGH detection voltage: DC 3V or higher \\ input frequency: Max. 50kHz \\ D24/D25: built-in 4.7kΩ pull-up \\ D18/D19: built-in 4.7kΩ pull-up  |
@@ Line 24: / Line 30: @@
 | ::: | ::: |  SRAM  | 4KB  |
 | ::: | ::: |  EEPROM  | 4KB  |
+**Markdown file:** [[https://www.ilogics.net/docs/downloads:mpino:en:mpino_8a4t_s?do=export_raw|Download MPINO-8A4T-S.md]]
 ===== Digital inputs =====
+[[:en-us_guide:wiring#digital_input_one_channel_check|See the one-channel digital-input check before wiring for the first time. →]]
 ^ Terminal ^ Arduino Pin ^ Input Configuration ^ Terminals and Wiring Example ^
 | P0~P3 | D0~D3 | 4 digital inputs, sharing COM0 |  {{:en-us_products:mpino-8a4t-s-digital-input.svg?740|MPINO-8A4T-S digital input terminals and NPN/PNP wiring}}  |
@@ Line 153: / Line 162: @@
 </code>
+===== STATUS LED =====
+The MPINO-8A4T-S STATUS LED is an indicator mounted on the board. You can use it to show the operating state of your program.
+The STATUS LED is connected to digital pin D20. In a sketch, use ''LED_BUILTIN'' in place of D20. Set ''pinMode(LED_BUILTIN, OUTPUT)'' before controlling it. ''digitalWrite(LED_BUILTIN, HIGH)'' turns the LED on; ''digitalWrite(LED_BUILTIN, LOW)'' turns it off.
+**Note:** The STATUS LED is on the board and is separate from the external output terminals.
+==== Example · Blink the STATUS LED ====
+This example turns the STATUS LED on and off at 0.5-second intervals.
+<code cpp>
+void setup() {
+  pinMode(LED_BUILTIN, OUTPUT);
+}
+void loop() {
+  digitalWrite(LED_BUILTIN, HIGH);  // LED on
+  delay(500);
+  digitalWrite(LED_BUILTIN, LOW);   // LED off
+  delay(500);
+}
+</code>
 ===== Transistor outputs =====
+[[:en-us_guide:wiring#sink_transistor_output_one_channel_check|See the one-channel SINK transistor-output check before wiring for the first time. →]]
 ^ Terminal ^ Arduino Pin ^ Output Type ^ Maximum Rating ^ Terminals and Wiring Example ^
-| P32 | D32 | SINK outputs | DC 100V, 1A/1 points |  {{:en-us_products:mpino-8a4t-s-transistor-output.svg?698|MPINO-8A4T-S transistor output terminals and SINK wiring}}  |
+| P32 | D32 | SINK outputs | DC 100V, 1A/1 point |  {{:en-us_products:mpino-8a4t-s-transistor-output.svg?698|MPINO-8A4T-S transistor output terminals and SINK wiring}}  |
-| P33 | D33 | SINK outputs | DC 100V, 1A/1 points | ::: |
+| P33 | D33 | SINK outputs | DC 100V, 1A/1 point | ::: |
-| P34 | D34 | SINK outputs | DC 100V, 1A/1 points | ::: |
+| P34 | D34 | SINK outputs | DC 100V, 1A/1 point | ::: |
-| P35 | D35 | SINK outputs | DC 100V, 1A/1 points | ::: |
+| P35 | D35 | SINK outputs | DC 100V, 1A/1 point | ::: |
 The transistor outputs use a SINK configuration: when ON, the output terminal connects to V-. Connect the external DC supply for the load to V+ and V-.
@@ Line 718: / Line 753: @@
 **Related built-in functions**
-=== Function example · LS Industrial Systems Cnet SLave: ICnetMem(), ICnetAdr(), ICnetInit(), ICnet() ===
+=== Function example · LS Industrial Systems Cnet Slave: ICnetMem(), ICnetAdr(), ICnetInit(), ICnet() ===
 **Function prototype**
@@ Line 762: / Line 797: @@
 </code>
-[[:en-us_products:mpino_series|← MPINO Series comparison (Korean)]]
+[[https://www.ilogics.net/en-us/products/mpino-8a4t-s|View MPINO-8A4T-S price and purchase options]]
+[[:en-us_products:mpino_series|← MPINO Series comparison (Korean)]]