Differences

This shows you the differences between two versions of the page.

--- en-us_products:mpino_studio2:first_project [2026/09/10 00:23] – 바깥 편집 127.0.0.1
+++ en-us_products:mpino_studio2:first_project [2026/09/14 12:24] (current) – external edit 127.0.0.1
@@ Line 16: / Line 16: @@
   * A PC with MPINO Studio 2 installed
   * An MPINO-8A4R(T)-S board
-  * An MP download cable
+  * An MP download cable (for MPINO-8A4R(T)-S)
   * A P0 input signal wired according to the product manual if you will perform the live input test
@@ Line 27: / Line 27: @@
 {{ :products:mpino_studio2:first-run-window-marked.svg?1200 |Figure 1. Default project opened at first launch }}
-On the first launch, a notice about automatic error reporting appears once. Read the notice and select **OK** to close it. You can later change this option under **Settings → General → Send error reports automatically**.
+On the first launch, a notice about automatic error reporting appears once. Read the notice and select **OK** to close it. You can later change this option under **File → Preferences → General → Send error reports automatically**.
 {{ :products:mpino_studio2:chfirst-run-notice.png?480 |Figure 2. Error-reporting notice displayed at first launch }}
@@ Line 36: / Line 36: @@
   - **① Menu bar:** File, Edit, View, Run, Settings, and Help
-  - **② Activity bar:** Explorer, board and memory information, ladder tools, symbols, Serial Monitor, and settings
+  - **② Activity bar:** Explorer, Ladder Settings, Ladder Pin Map Settings, Library, Symbols, Serial Monitor, and Settings
   - **③ Sidebar:** Project and board information for the selected activity
   - **④ Editor:** Arduino C code or ladder circuit editor
@@ Line 53: / Line 53: @@
   - Choose **② Select**, press ''Enter'' on the card, or double-click it. Press ''Esc'' to cancel.
   - When the new project opens, press ''Ctrl+S'' to choose its name and save location.
+  - Open **Settings → Ladder Pin Map Settings**, select **Use** for the ''P0'' and ''P32'' rows, and select **OK**.
+  - Press ''Ctrl+S'' to save the pin map settings in the project.
 {{ :products:mpino_studio2:board-select-modal-marked.svg?1100 |Figure 4. Board selection window with MPINO-8A4R(T)-S selected }}
@@ Line 122: / Line 124: @@
 > **Caution:** Uploading does not start until a port is selected.
-  - Connect the board to the PC with the MP download cable.
+  - Connect the MPINO-8A4R(T)-S board to the PC with the MP download cable.
+  - In Windows **Device Manager → Ports (COM & LPT)**, check for ''USB Serial Port (COMx)''. If it does not appear, install the [[https://www.ilogics.net/en-us/resources/downloads/driver/1|FTDI driver for the MP download cable]] and reconnect the cable.
   - Select **① Select Port** at the right side of the status bar.
   - Choose the required port, such as ''COM3'', from **② the open port list**.
@@ Line 142: / Line 145: @@
 ==== Real-Time Ladder Monitoring ====
-Before using real-time monitoring, select a communication port under **Settings → Ladder Settings → Monitoring Port**, then build and upload again. After that, press ''Ctrl+M'' or select **① Monitoring ON** in the ladder view.
+Before using real-time monitoring, select a communication port under **File → Preferences → Ladder Settings → Monitoring Port**, then build and upload again. After that, press ''Ctrl+M'' or select **① Monitoring ON** in the ladder view.
 When a physical input signal reaches P0, **② the P0 contact** and **③ the P32 coil** are highlighted. Press ''Esc'' to stop monitoring.
@@ Line 171: / Line 174: @@
   * You selected the correct port and uploaded the project.
   * The P32 coil's monitoring state changes with the P0 input.
+===== Follow Along with MPAINO-8A8R(T) =====
+For MPAINO-8A8R(T), the first input is ''P0'' and the first output is ''P64''. Use the editing, build, upload, and monitoring controls described above, with the board, output address, and PC connection shown below.
+Connect the USB download port on the MPAINO-8A8R(T) CPU module to the PC with a standard USB cable. In Windows **Device Manager → Ports (COM & LPT)**, check for ''Silicon Labs CP210x USB to UART Bridge (COMx)''. If it does not appear, install the [[https://www.ilogics.net/en-us/resources/downloads/driver/2|CP210x driver for models with a built-in bridge]] and reconnect the cable.
+^ Item ^ MPINO-8A4R(T)-S example on this page ^ MPAINO-8A8R(T) ^
+| Board selection | ''MPINO-8A4R(T)-S'' | ''MPAINO-8A8R(T)'' |
+| First digital input | ''P0'' | ''P0'' |
+| First digital output | ''P32'' | ''P64'' |
+  - Select the ''MPAINO-8A8R(T)'' board under **File → New**, then save the project.
+  - Under **Settings → Ladder Pin Map Settings**, check that **Use** is enabled for input ''P0'' and output ''P64'', then save. Confirm that the relay (R) or transistor (T) output type matches the delivered product.
+  - Place an NO contact at ''P0'' and an output coil at ''P64'' on the first row of ''ladderLoop''. Figure 5 shows the MPINO example; enter ''P64'' instead of its ''P32'' coil address.
+  - Follow **Build → Select the COM port above in the status bar → Upload → Verify Operation**. Check wiring against the [[:en-us_products:mpaino_8a8r|MPAINO-8A8R details]] or the specification for your T model.
+Other MPAINO models can have different I/O counts and module configurations. Check the pin map of the selected project board and use the addresses for your model.
 ===== Troubleshooting =====
@@ Line 176: / Line 197: @@
 ^ Symptom ^ What to check ^
 | Upload stops immediately. | Make sure a port is selected in the status bar. |
-| P0 or P32 does not behave as expected. | Check that the selected board matches the physical product and that both cell addresses are correct. |
+| P0 or the output does not behave as expected. | Check that the selected board matches the physical product. Under **Settings → Ladder Pin Map Settings**, confirm **Use** for input ''P0'' and the model's output address (''P32'' or ''P64''). |
 | The ladder does not show energized elements. | Set the monitoring port, then build and upload the project again. |
 | The build fails. | Read the last error in Build Output and check the ''main'' code syntax. |
+===== Related Documentation =====
+  * [[en-us_products:mpino_studio2:monitoring|Phase 6 · Serial and Ladder Monitoring]]
+  * [[en-us_products:mpino_studio2:menus_settings#ladder_pin_map_settings|Phase 7 · Ladder Pin Map Settings]]
 [[:en-us_products:mpino_studio2|← Return to the MPINO STUDIO 2 manual]]