ILOGICS Product Documentation

User Tools

Site Tools

Trace:
en-us_products:mpino_studio2:first_project

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
en-us_products:mpino_studio2:first_project [2026/09/11 11:11] – 바깥 편집 127.0.0.1en-us_products:mpino_studio2:first_project [2026/10/03 13:15] (current) – external edit 127.0.0.1
Line 8: Line 8:
 {{ :en-us_products:mpino_studio2:first-project-flow.svg?1000 |Workflow from creating the first project to checking the running board }} {{ :en-us_products:mpino_studio2:first-project-flow.svg?1000 |Workflow from creating the first project to checking the running board }}
  
-> **About the screenshots:** The screenshots show the Korean interface. Button positions and keyboard shortcuts are the same as described below.+> **About the screenshots:** The screenshots show the English interface.
  
 ===== 1. Before You Begin ===== ===== 1. Before You Begin =====
Line 16: Line 16:
   * A PC with MPINO Studio 2 installed   * A PC with MPINO Studio 2 installed
   * An MPINO-8A4R(T)-S board   * An MPINO-8A4R(T)-S board
-  * An MP download cable+  * An MP download cable (for MPINO-8A4R(T)-S)
   * A P0 input signal wired according to the product manual if you will perform the live input test   * A P0 input signal wired according to the product manual if you will perform the live input test
  
Line 25: Line 25:
 MPINO Studio 2 opens **① an Untitled project** that you can edit immediately. The Explorer already contains **② the ''main'' code tab** and **③ the ''ladderLoop'' ladder tab**. MPINO Studio 2 opens **① an Untitled project** that you can edit immediately. The Explorer already contains **② the ''main'' code tab** and **③ the ''ladderLoop'' ladder tab**.
  
-{{ :products:mpino_studio2:first-run-window-marked.svg?1200 |Figure 1. Default project opened at first launch }}+{{ :en-us_products:mpino_studio2:first-run-window-marked.svg?1200 |Figure 1. Default project opened at first launch }}
  
-On the first launch, a notice about automatic error reporting appears once. Read the notice and select **OK** to close it. You can later change this option under **Settings → General → Send error reports automatically**.+On the first launch, a notice about automatic error reporting appears once. Read the notice and select **OK** to close it. You can later change this option under **File → Preferences → General → Send error reports automatically**.
  
-{{ :products:mpino_studio2:chfirst-run-notice.png?480 |Figure 2. Error-reporting notice displayed at first launch }}+{{ :en-us_products:mpino_studio2:chfirst-run-notice.png?480 |Figure 2. Error-reporting notice displayed at first launch }}
  
 ===== 3. Learn the Six Screen Areas ===== ===== 3. Learn the Six Screen Areas =====
Line 36: Line 36:
  
   - **① Menu bar:** File, Edit, View, Run, Settings, and Help   - **① Menu bar:** File, Edit, View, Run, Settings, and Help
-  - **② Activity bar:** Explorer, board and memory information, ladder tools, symbols, Serial Monitor, and settings+  - **② Activity bar:** Explorer, Ladder Settings, Ladder Pin Map Settings, Library, Symbols, Serial Monitor, and Settings
   - **③ Sidebar:** Project and board information for the selected activity   - **③ Sidebar:** Project and board information for the selected activity
   - **④ Editor:** Arduino C code or ladder circuit editor   - **④ Editor:** Arduino C code or ladder circuit editor
Line 42: Line 42:
   - **⑥ Status bar:** Current status and port selector   - **⑥ Status bar:** Current status and port selector
  
-{{ :products:mpino_studio2:app-overview-layout-marked.svg?1200 |Figure 3. Main areas of the MPINO Studio 2 window }}+{{ :en-us_products:mpino_studio2:app-overview-layout-marked.svg?1200 |Figure 3. Main areas of the MPINO Studio 2 window }}
  
 **⑦ Ready** at the lower left is a static label. Use **⑧ Select Port** at the lower right to choose the serial port for uploading. **⑦ Ready** at the lower left is a static label. Use **⑧ Select Port** at the lower right to choose the serial port for uploading.
Line 56: Line 56:
   - Press ''Ctrl+S'' to save the pin map settings in the project.   - Press ''Ctrl+S'' to save the pin map settings in the project.
  
-{{ :products:mpino_studio2:board-select-modal-marked.svg?1100 |Figure 4. Board selection window with MPINO-8A4R(T)-S selected }}+{{ :en-us_products:mpino_studio2:board-select-modal-marked.svg?1100 |Figure 4. Board selection window with MPINO-8A4R(T)-S selected }}
  
 Selecting the board does not create a file on disk. The name and location of the ''.mp2'' project file are set when you save it. Selecting the board does not create a file on disk. The name and location of the ''.mp2'' project file are set when you save it.
Line 70: Line 70:
   - Confirm that your screen matches the figure below.   - Confirm that your screen matches the figure below.
  
-{{ :products:mpino_studio2:ladder-editor-toolbar-marked-phase1.svg?1200 |Figure 5. Ladder circuit with the P0 contact and P32 output coil }}+{{ :en-us_products:mpino_studio2:ladder-editor-toolbar-marked-phase1.svg?1200 |Figure 5. Ladder circuit with the P0 contact and P32 output coil }}
  
 Press ''Enter'' on **① the selected cell**, or double-click it, to open the edit window. Enter the value in **② the address field**, then choose **③ OK**. Contacts and coils use the same style of input window, so check the selected cell and address before confirming. Press ''Enter'' on **① the selected cell**, or double-click it, to open the edit window. Enter the value in **② the address field**, then choose **③ OK**. Contacts and coils use the same style of input window, so check the selected cell and address before confirming.
  
-{{ :products:mpino_studio2:ladder-cell-edit-modal-marked.svg?1050 |Figure 6. Entering P0 in the contact edit window }}+{{ :en-us_products:mpino_studio2:ladder-cell-edit-modal-marked.svg?1050 |Figure 6. Entering P0 in the contact edit window }}
  
 ==== Common Ladder Tools ==== ==== Common Ladder Tools ====
Line 116: Line 116:
   - The build succeeded if the final line contains **② ''[arduino-cli exit 0]''**.   - The build succeeded if the final line contains **② ''[arduino-cli exit 0]''**.
  
-{{ :products:mpino_studio2:build-output-panel-marked.svg?1200 |Figure 8. Build Output after a successful build }}+{{ :en-us_products:mpino_studio2:build-output-panel-marked.svg?1200 |Figure 8. Build Output after a successful build }}
  
 If the build fails, start with the error summary and the last part of the log. Check the selected board, cell addresses, and code syntax in that order. If the build fails, start with the error summary and the last part of the log. Check the selected board, cell addresses, and code syntax in that order.
Line 124: Line 124:
 > **Caution:** Uploading does not start until a port is selected. > **Caution:** Uploading does not start until a port is selected.
  
-  - Connect the board to the PC with the MP download cable.+  - Connect the MPINO-8A4R(T)-S board to the PC with the MP download cable. 
 +  - In Windows **Device Manager → Ports (COM & LPT)**, check for ''USB Serial Port (COMx)''. If it does not appear, install the [[https://www.ilogics.net/en-us/resources/downloads/driver/1|FTDI driver for the MP download cable]] and reconnect the cable.
   - Select **① Select Port** at the right side of the status bar.   - Select **① Select Port** at the right side of the status bar.
   - Choose the required port, such as ''COM3'', from **② the open port list**.   - Choose the required port, such as ''COM3'', from **② the open port list**.
Line 130: Line 131:
   - Confirm that the upload log continues below the build log and ends normally.   - Confirm that the upload log continues below the build log and ends normally.
  
-{{ :products:mpino_studio2:statusbar-port-picker-marked.svg?1200 |Figure 9. Selecting the upload port from the status bar }}+{{ :en-us_products:mpino_studio2:statusbar-port-picker-marked.svg?1200 |Figure 9. Selecting the upload port from the status bar }}
  
 The port list refreshes automatically when the drop-down opens. You can cancel an upload from the bottom panel while it is running. The port list refreshes automatically when the drop-down opens. You can cancel an upload from the bottom panel while it is running.
Line 140: Line 141:
 Select **① Serial Monitor** in the Activity bar. Choose **② the baud rate** and **③ character encoding**, then select **④ Connect**. Use **⑤ the ASCII/HEX control** to change the display mode, and check **⑥ the connection state** at the right. Select **① Serial Monitor** in the Activity bar. Choose **② the baud rate** and **③ character encoding**, then select **④ Connect**. Use **⑤ the ASCII/HEX control** to change the display mode, and check **⑥ the connection state** at the right.
  
-{{ :products:mpino_studio2:serial-monitor-panel-marked.svg?1200 |Figure 10. Connected Serial Monitor }}+{{ :en-us_products:mpino_studio2:serial-monitor-panel-marked.svg?1200 |Figure 10. Connected Serial Monitor }}
  
 ==== Real-Time Ladder Monitoring ==== ==== Real-Time Ladder Monitoring ====
  
-Before using real-time monitoring, select a communication port under **Settings → Ladder Settings → Monitoring Port**, then build and upload again. After that, press ''Ctrl+M'' or select **① Monitoring ON** in the ladder view.+Before using real-time monitoring, select a communication port under **File → Preferences → Ladder Settings → Monitoring Port**, then build and upload again. After that, press ''Ctrl+M'' or select **① Monitoring ON** in the ladder view.
  
 When a physical input signal reaches P0, **② the P0 contact** and **③ the P32 coil** are highlighted. Press ''Esc'' to stop monitoring. When a physical input signal reaches P0, **② the P0 contact** and **③ the P32 coil** are highlighted. Press ''Esc'' to stop monitoring.
  
-{{ :products:mpino_studio2:ladder-live-monitoring-marked.svg?1200 |Figure 11. Real-time ladder monitoring with P0 and P32 energized }}+{{ :en-us_products:mpino_studio2:ladder-live-monitoring-marked.svg?1200 |Figure 11. Real-time ladder monitoring with P0 and P32 energized }}
  
 ===== 10. Phase 1 Shortcuts ===== ===== 10. Phase 1 Shortcuts =====
Line 173: Line 174:
   * You selected the correct port and uploaded the project.   * You selected the correct port and uploaded the project.
   * The P32 coil's monitoring state changes with the P0 input.   * The P32 coil's monitoring state changes with the P0 input.
 +
 +===== Follow Along with MPAINO-8A8R(T) =====
 +
 +For MPAINO-8A8R(T), the first input is ''P0'' and the first output is ''P64''. Use the editing, build, upload, and monitoring controls described above, with the board, output address, and PC connection shown below.
 +
 +Connect the USB download port on the MPAINO-8A8R(T) CPU module to the PC with a standard USB cable. In Windows **Device Manager → Ports (COM & LPT)**, check for ''Silicon Labs CP210x USB to UART Bridge (COMx)''. If it does not appear, install the [[https://www.ilogics.net/en-us/resources/downloads/driver/2|CP210x driver for models with a built-in bridge]] and reconnect the cable.
 +
 +^ Item ^ MPINO-8A4R(T)-S example on this page ^ MPAINO-8A8R(T) ^
 +| Board selection | ''MPINO-8A4R(T)-S'' | ''MPAINO-8A8R(T)'' |
 +| First digital input | ''P0'' | ''P0'' |
 +| First digital output | ''P32'' | ''P64'' |
 +
 +  - Select the ''MPAINO-8A8R(T)'' board under **File → New**, then save the project.
 +  - Under **Settings → Ladder Pin Map Settings**, check that **Use** is enabled for input ''P0'' and output ''P64'', then save. Confirm that the relay (R) or transistor (T) output type matches the delivered product.
 +  - Place an NO contact at ''P0'' and an output coil at ''P64'' on the first row of ''ladderLoop''. Figure 5 shows the MPINO example; enter ''P64'' instead of its ''P32'' coil address.
 +  - Follow **Build → Select the COM port above in the status bar → Upload → Verify Operation**. Check wiring against the [[:en-us_products:mpaino_8a8r|MPAINO-8A8R details]] or the specification for your T model.
 +
 +Other MPAINO models can have different I/O counts and module configurations. Check the pin map of the selected project board and use the addresses for your model.
  
 ===== Troubleshooting ===== ===== Troubleshooting =====
Line 178: Line 197:
 ^ Symptom ^ What to check ^ ^ Symptom ^ What to check ^
 | Upload stops immediately. | Make sure a port is selected in the status bar. | | Upload stops immediately. | Make sure a port is selected in the status bar. |
-| P0 or P32 does not behave as expected. | Check that the selected board matches the physical product and that **Use** is selected for both addresses under **Settings → Ladder Pin Map Settings**. |+| P0 or the output does not behave as expected. | Check that the selected board matches the physical product. Under **Settings → Ladder Pin Map Settings**, confirm **Use** for input ''P0'' and the model's output address (''P32'' or ''P64''). |
 | The ladder does not show energized elements. | Set the monitoring port, then build and upload the project again. | | The ladder does not show energized elements. | Set the monitoring port, then build and upload the project again. |
 | The build fails. | Read the last error in Build Output and check the ''main'' code syntax. | | The build fails. | Read the last error in Build Output and check the ''main'' code syntax. |
en-us_products/mpino_studio2/first_project.1789092667.txt.gz · Last modified: by 127.0.0.1
Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki