ILOGICS Product Documentation

User Tools

Site Tools

Trace: • first_project • mpino_studio2 • mpino_8a4t_s • ladder_editing • analog_output_pwm • mpaino
en-us_products:mpino_studio2:first_project

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
en-us_products:mpino_studio2:first_project [2026/09/12 22:54] – 바깥 편집 127.0.0.1en-us_products:mpino_studio2:first_project [2026/09/14 12:24] (current) – external edit 127.0.0.1
Line 16: Line 16:
   * A PC with MPINO Studio 2 installed   * A PC with MPINO Studio 2 installed
   * An MPINO-8A4R(T)-S board   * An MPINO-8A4R(T)-S board
-  * An MP download cable+  * An MP download cable (for MPINO-8A4R(T)-S)
   * A P0 input signal wired according to the product manual if you will perform the live input test   * A P0 input signal wired according to the product manual if you will perform the live input test
  
Line 36: Line 36:
  
   - **① Menu bar:** File, Edit, View, Run, Settings, and Help   - **① Menu bar:** File, Edit, View, Run, Settings, and Help
-  - **② Activity bar:** Explorer, board and memory information, ladder tools, symbols, Serial Monitor, and settings+  - **② Activity bar:** Explorer, Ladder Settings, Ladder Pin Map Settings, Library, Symbols, Serial Monitor, and Settings
   - **③ Sidebar:** Project and board information for the selected activity   - **③ Sidebar:** Project and board information for the selected activity
   - **④ Editor:** Arduino C code or ladder circuit editor   - **④ Editor:** Arduino C code or ladder circuit editor
Line 124: Line 124:
 > **Caution:** Uploading does not start until a port is selected. > **Caution:** Uploading does not start until a port is selected.
  
-  - Connect the board to the PC with the MP download cable.+  - Connect the MPINO-8A4R(T)-S board to the PC with the MP download cable. 
 +  - In Windows **Device Manager → Ports (COM & LPT)**, check for ''USB Serial Port (COMx)''. If it does not appear, install the [[https://www.ilogics.net/en-us/resources/downloads/driver/1|FTDI driver for the MP download cable]] and reconnect the cable.
   - Select **① Select Port** at the right side of the status bar.   - Select **① Select Port** at the right side of the status bar.
   - Choose the required port, such as ''COM3'', from **② the open port list**.   - Choose the required port, such as ''COM3'', from **② the open port list**.
Line 144: Line 145:
 ==== Real-Time Ladder Monitoring ==== ==== Real-Time Ladder Monitoring ====
  
-Before using real-time monitoring, select a communication port under **Settings → Ladder Settings → Monitoring Port**, then build and upload again. After that, press ''Ctrl+M'' or select **① Monitoring ON** in the ladder view.+Before using real-time monitoring, select a communication port under **File → Preferences → Ladder Settings → Monitoring Port**, then build and upload again. After that, press ''Ctrl+M'' or select **① Monitoring ON** in the ladder view.
  
 When a physical input signal reaches P0, **② the P0 contact** and **③ the P32 coil** are highlighted. Press ''Esc'' to stop monitoring. When a physical input signal reaches P0, **② the P0 contact** and **③ the P32 coil** are highlighted. Press ''Esc'' to stop monitoring.
Line 176: Line 177:
 ===== Follow Along with MPAINO-8A8R(T) ===== ===== Follow Along with MPAINO-8A8R(T) =====
  
-For MPAINO-8A8R(T), the first input is ''P0'' and the first output is ''P64''. Follow the same editing, build, upload and monitoring steps on this page, changing the board and output address as shown below.+For MPAINO-8A8R(T), the first input is ''P0'' and the first output is ''P64''. Use the editing, build, upload, and monitoring controls described above, with the board, output address, and PC connection shown below. 
 + 
 +Connect the USB download port on the MPAINO-8A8R(T) CPU module to the PC with a standard USB cable. In Windows **Device Manager → Ports (COM & LPT)**, check for ''Silicon Labs CP210x USB to UART Bridge (COMx)''. If it does not appear, install the [[https://www.ilogics.net/en-us/resources/downloads/driver/2|CP210x driver for models with a built-in bridge]] and reconnect the cable.
  
 ^ Item ^ MPINO-8A4R(T)-S example on this page ^ MPAINO-8A8R(T) ^ ^ Item ^ MPINO-8A4R(T)-S example on this page ^ MPAINO-8A8R(T) ^
Line 186: Line 189:
   - Under **Settings → Ladder Pin Map Settings**, check that **Use** is enabled for input ''P0'' and output ''P64'', then save. Confirm that the relay (R) or transistor (T) output type matches the delivered product.   - Under **Settings → Ladder Pin Map Settings**, check that **Use** is enabled for input ''P0'' and output ''P64'', then save. Confirm that the relay (R) or transistor (T) output type matches the delivered product.
   - Place an NO contact at ''P0'' and an output coil at ''P64'' on the first row of ''ladderLoop''. Figure 5 shows the MPINO example; enter ''P64'' instead of its ''P32'' coil address.   - Place an NO contact at ''P0'' and an output coil at ''P64'' on the first row of ''ladderLoop''. Figure 5 shows the MPINO example; enter ''P64'' instead of its ''P32'' coil address.
-  - Follow **Build → Select Port and Upload → Verify Operation** above. Check wiring against the [[:en-us_products:mpaino_8a8r|MPAINO-8A8R details]] or the specification for your T model.+  - Follow **Build → Select the COM port above in the status bar → Upload → Verify Operation**. Check wiring against the [[:en-us_products:mpaino_8a8r|MPAINO-8A8R details]] or the specification for your T model.
  
 Other MPAINO models can have different I/O counts and module configurations. Check the pin map of the selected project board and use the addresses for your model. Other MPAINO models can have different I/O counts and module configurations. Check the pin map of the selected project board and use the addresses for your model.
en-us_products/mpino_studio2/first_project.1789221299.txt.gz · Last modified: by 127.0.0.1
Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki