en-us_products:mp_studio:menus_settings

This is an old revision of the document!


MP STUDIO 2 Phase 9 · Menus and Settings

This page describes the menu items and option settings of MP STUDIO 2, the language and themes, printing, the Modbus RTU master, autosave, problem reports and help. Menu items show their keyboard shortcuts on the right.

Project Menu

Figure 1. The Project menu

Item Shortcut Action
New Project Ctrl+N Creates a new project with an empty ladder. The model setting is carried over.
Open Project Ctrl+O Opens an .mpx or .mpl project.
Save Project Ctrl+S Saves the current project in the .mpx format. If you opened an .mpl file, it is saved as an .mpx file with the same name, and the original .mpl is left as it is.
Save As Ctrl+Alt+S Saves under a different name or location.
Print · Page Setup · Print Preview Ctrl+P Opens the Windows print dialog. Choose the paper and preview there.
Open Example — Opens the bundled example program.
Recover Autosave… — Opens a remaining autosave. See Autosave and Recovery.
Recent files — The five most recently opened projects are listed at the bottom of the menu. Hover over one to see its full path.

If there are unsaved changes when you run New Project, Open Project or Open Example, or close the window, you are asked whether to save them. If the file you are about to save has been changed by another program, you are first asked whether to overwrite it.

Edit and Search Menus

Figure 2. The Edit menu Figure 3. The Search menu

The items of the Edit and Search menus are described in Phase 3 · Ladder Editing and Phase 6 · Program Check. All shortcuts are listed in the Quick Reference.

View Menu

Item Shortcut Action
Show Symbols · Show Comments — Shows symbol names and comments on the cells.
Bookmark List — Shows or hides the bookmark (Mark) list at the bottom of the Functions panel.
Symbol Rail · Functions · Inspector · Watch · Command Bar · Status Pills Alt+1 to Alt+7 Shows or hides each panel.
Hide All Panels Alt+0 Hides all panels.
Zoom In · Zoom Out · Fit to Width Ctrl+= · Ctrl+- Changes the display size of the ladder. Ctrl+0 returns to 100%.
Quick Actions Ctrl+K Finds a menu item by name and runs it.

Run Menu

Figure 4. The Run menu

Item Shortcut Described in
Connect — Phase 6
Download Ctrl+T Phase 6
Firmware Download · Firmware Version — Phase 6
Monitoring Ctrl+M Phase 7
Simulation — Phase 8
Used Data — Phase 5
Data Table — Phase 7
Program Memory — Phase 6
FORCE INPUT / OUTPUT — Phase 7
Clear EEPROM — Phase 6
Set Device Clock… — Device Clock (RTC)
Mnemonic — Phase 6

Setting Menu

Figure 5. The Setting menu

Item Action
Communication Port Sets the download channel and the serial channels. Phase 6
언어: 한국어 · Language: English · 言語: 日本語 Changes the display language.
Option Sets the grid, duplicate coil check, timer base, fonts, colors and brand name.
Data Memory Sets the memory area sizes and retentive ranges. Phase 5
Symbol Opens the symbol table. Phase 5
CLCD Screen Editor Creates screens to show on a character LCD. The ladder shows a screen with the CSCR function. CLCD Screen Editor
7-Segment Screen Editor Creates screens to show on a 7-segment display. The ladder shows a screen with the FSCR function. 7-Segment Display
Device Selects the model and expansion modules. Phase 1
Modbus RTU Master Sets up Modbus RTU master communication. Modbus Device Table
RTC (Clock)… Sets the start address of the D area (16 words) where the device writes the date, time and status of an external DS3231 module every 0.1 seconds. Device Clock (RTC)
User Protocol… Defines, per communication port, the frames and transactions to exchange with devices that do not use Modbus (V1.3.0 and later). User Protocol
Theme: Modern Dark · VS Code · Light Changes the screen theme.

Options

Select Setting → Option or click the Options button in the top band to open the Option window. Choose an item in the navigation on the left to see its settings and a preview on the right.

Figure 6. The Option window

  • ① Search settings: finds items by setting name.
  • ② Navigation: Grid, FONT, COLOR and Brand name
  • ③ Settings area
  • ④ Preview: changed settings are reflected in the ladder preview right away.
  • ⑤ Cancel, Apply and OK: Apply applies the changes without closing the window. Reset all colors and fonts at the bottom left returns all customized colors and fonts to their defaults, and the number of customized items is shown next to it.
Navigation Settings
Grid Cell width and height (Grid width, Grid height), the number of cells per row (Columns per row), Check for duplicate coils, and Timer base
FONT Grid Font (addresses, symbols, comments and monitor values), Header Font (row numbers), Interface font (menus and windows), Code font (places that show addresses and values in a fixed-width font)
COLOR Colors for the Theme, Ladder, Function blocks, Monitor & check, and Interface
Brand name The name shown in the window title

Columns per row, Check for duplicate coils and Timer base apply only to the project. Custom colors apply to every theme, and colors you leave unset follow the selected theme. Printing always uses paper colors (black).

Figure 7. COLOR › Ladder settings and the preview

Timer Base

In Grid, use Timer base to choose the time unit that timers and clocks (@n, @Fn) count in: 10 ms (default) or 1 ms (V1.3.0 and later). You can choose it only while a project is open, and a new project starts with 10 ms.

Item 10 ms (default) 1 ms
Set value written as a number only (TON T0 100) 1 second 0.1 seconds
Set value with a unit (TON T0 1s) 1 second 1 second
@100 ON for one scan every second ON for one scan every 0.1 seconds
@F100 2-second period 0.2-second period
Longest timer time (BT, T, DT) 2.55 s, 655 s, 497 days 0.255 s, 65.5 s, 49.7 days

Even with 1 ms, timers check the time once per scan, so the real resolution cannot be finer than the scan time. You do not need to change the device firmware. Values written as ×10 ms (the timeout of the Modbus RTU Master and the EEPROM update cycle of Data Memory) and SCAN TIME stay in 10 ms units regardless of the timer base. The 1 ms base uses 5 more bytes of device RAM, and if there is not enough RAM, a compile error is shown.

When you change the base and click OK (or Apply), the Change timer base window shows the number of affected cells, if there are any.

  • Fix values too (keep the same time): changes the timer set values and clock numbers written as numbers so that the times stay the same. From 10 ms to 1 ms they are multiplied by 10; from 1 ms to 10 ms they are divided by 10 (the remainder is dropped, and a result below 1 becomes 1).
  • Keep numbers: changes only the base. The times become 1/10 when you go from 10 ms to 1 ms, and 10 times longer when you go from 1 ms to 10 ms.
  • Cancel: returns to the Option window without changing the base.

Timer set values written as variables, cells that read the current value of a timer, and timer cells that will go out of range (red) after the change are counted separately in the window, so check them yourself. A single Ctrl+Z undoes the new base and the adjusted values together. To keep them in the file, save the project. A project that uses 1 ms shows Timer 1 ms in the status pills. A .mpx file saved with 1 ms cannot be opened by V1.2.0 and earlier.

Themes and Language

In the Setting menu, choose Theme: Modern Dark, Theme: VS Code or Theme: Light.

Modern Dark VS Code Light

Use 언어: 한국어, Language: English and 言語: 日本語 in the Setting menu to change the language of the menus and windows. The three items are always shown in their own language, whichever language the screen is in, so you can return to English from any screen by choosing Language: English (in Korean the menu is named 설정, in Japanese 設定).

Figure 8. The Setting menu with the three language items

Printing

Select Project → Print (Ctrl+P) to lay out the ladder for printing and open the Windows print dialog. Page Setup and Print Preview open the same print dialog. Choose the paper orientation, margins and printer in the print dialog. To save a PDF, choose Microsoft Print to PDF as the printer.

Figure 9. One printed page

Modbus RTU Master

Select Setting → Modbus RTU Master to open a window for setting up the registers that the device, acting as a Modbus RTU master, reads from and writes to other devices. New projects and projects that have a device table open the Modbus Device Table window; projects that have only a list made in the previous MP STUDIO (such as the bundled Modbus example) open the list window below.

Figure 10. The MODBUS MASTER SETTING window (bundled Modbus example)

  1. In ① Communication Port, choose the channel to use as the master (Comm Port 1 to Comm Port 3), and set the Baud Rate, Data Bits, Stop Bits, Parity, Timeout (×10 ms) and Delay (ms).
  2. Click ② Add to add an item. Sort sorts the items.
  3. In ③ the item table, enter the Modbus Code (for example WORD READ ( FC03 ) or WORD WRITE ( FC06 )), Slave ID, Address, Binding (the device memory that exchanges the value, for example D10) and Description on each row. Click Delete at the end of a row to remove that item.
  4. Click OK to save.

When you click OK, the communication settings of the selected channel change to the values above, its mode is set to Modbus RTU Master, and download on that channel is turned off.

Click Move to table at the bottom left of the window to move this list into the Modbus Device Table. Moving it changes the compiled program (it then uses the device table's new communication method). Use Edit → Undo (Ctrl+Z) to move it back.

Autosave and Recovery

MP STUDIO 2 automatically saves the project you are editing. If the program closed without saving, the Recover autosave window appears the next time you start it.

  • Yes: opens the autosaved copy.
  • No: deletes the autosaved copy.
  • Cancel: keeps the autosaved copy without deleting it. You can open it later from Project → Recover Autosave….

Figure 11. The Recover autosave window

Help Menu

Figure 12. The Help menu

Item Action
About MP STUDIO 2 Shows the program version and information.
Homepage Opens the ILOGICS homepage.
SW Manual Opens the software manual.
HW Manual Opens the hardware manual of the selected model.
Report a Problem… Describe a problem, attach a screenshot or the project file, and send it to the developer.
Request an Improvement… Sends a feature you would like or an improvement to the developer.
Send Error Reports Automatically When checked (✓), diagnostic information is sent automatically when an error occurs.

Report a Problem

Figure 13. The Report a Problem window

  1. Describe ① what happened (required).
  2. If needed, select ② Attach the open project (.mpx) and ③ Attach a screenshot. Diagnostic information (logs and system info) is always included.
  3. To get a reply, select ④ Leave contact details for a reply and enter your email address or phone number.
  4. Click Send.

After the program closes unexpectedly, you may be asked what you were doing when you start it again.

en-us_products/mp_studio/menus_settings.1794332161.txt.gz · Last modified: by 127.0.0.1

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki